Like MLG205 but larger and capable of folding down to deck to clear a boat cover, etc.• Diffuse fitting 45(dia)mm (max)• Total shroud 55(dia)mmPackaged DimensionsPackaged Dimensions35.3cm(Length) x 15.0cm(Width) x 6.5cm(Height)

Mount straight to deck of boat.• Requires 2 x No. 6 or 8 self tappers (not supplied) and one 6mm hole for wiring access• Black nylon body 55(dia)mm on short mast• ApprovedPackaged DimensionsPackaged Dimensions20.0cm(Length) x 25.0cm(Width)...

Combined port and starboard• Polished chrome housing mounted on insulated non-corrosive plastic base• 12V 5W Bulb• 100(L) x 77(W) x 50(H)mmPackaged DimensionsPackaged Dimensions17.0cm(Length) x 9.5cm(Width) x 6.0cm(Height)

Side mount with only 1 x No. 8 mounting screw required (not supplied). Sold as a pair.• Extra fixing location by plastic lug.• White body with red/green lens• LED light powered.• 97(L) x 60(W) x 35(D)mmPackaged DimensionsPackaged...

Our most popular port & starboard light sets.• Side mount with only 1 x No. 8 mounting screw required (not supplied)• Extra fixing location by plastic lug• Red / Green Lens• Powered by 12vdcProduct DimensionsLength97.0 mmWidth60.0...

Port and Starboard. Economical model. Standard design.• Side mount with 2 x No. 8 or 10 countersunk self tappers (not supplied).• White Finish Housing• Red/green lens• highpower long life LEDs. ( TheLEDs should out-last...

Port and Starboard. Economical model. Standard design.• Side mount with 2 x No. 8 or 10 countersunk self tappers (not supplied).• Black Finish Housing• Red/green lens• highpower long life LEDs. ( TheLEDs should out-last...

Port and Starboard. Economical model. Standard design.• Side mount with 2 x No. 8 or 10 countersunk self tappers (not supplied).• White Finish Housing• Red/green lens• 12V 5W festoon bulbs included.• Rubber sealing gasket...

Port and Starboard. Economical model. Standard design.• Side mount with 2 x No. 8 or 10 countersunk self tappers (not supplied).• Black Finish Housing• Red/green lens• 12V 5W festoon bulbs included.• Rubber sealing gasket...

Low cost, with 2 x clamps applied or can be permanently mountable or completely removable.• 600mm high (250mm for suction cap model - MLG015)• Handy On/Off switch on side - requires 3 x 'C' batteriesPackaged DimensionsPackaged...

Vertical mount. Similar to MLG010, except that it stands straight up.• Suitable for boats up to 7m long.• Requires 3 x 'C' batteries (not supplied).Packaged DimensionsPackaged Dimensions29.0cm(Length) x 19.0cm(Width) x 7.0cm(Height)

Horizontal mount. A massive 75(dia)mm suction cup holds the unit to almost any surface. Ideal for rubber, tin, fibreglass, power or sail. Simply wet cup and place, pointing the unit forward.• Has On/Off switch on body.• Suitable for boats up to...

A multifunction waterproof torch that turns on a flashing red beacon if dropped into water. Automatically turns off after 1 hour to preserve battery power.Modes of Operation:  •  White torch  •  White lantern ...

Brightness and affordability are two of the key benefits of OceanLED X-Series X4. With the X4, you can spend more time on the water with family and friends, whether you are cruising or fishing. Its low profile design enhances water penetration and...

This quality range of surface mount underwater lights provide years of service, without having to cut huge holes in the hull of your boat. All that’s required is a small hole for the cable (a few mm in diameter), and some short screws which...

This quality range of surface mount underwater lights provide years of service, without having to cut huge holes in the hull of your boat. All that’s required is a small hole for the cable (a few mm in diameter), and some short screws which...

This quality range of surface mount underwater lights provide years of service, without having to cut huge holes in the hull of your boat. All that’s required is a small hole for the cable (a few mm in diameter), and some short screws which...

This quality range of surface mount underwater lights provide years of service, without having to cut huge holes in the hull of your boat. All that’s required is a small hole for the cable (a few mm in diameter), and some short screws which...